cavity wall

英 [ˌkævəti ˈwɔːl]

美 [ˌkævəti ˈwɔːl]

n.  (有保暖作用的)空心墙，夹壁墙

医学

牛津词典

noun

• （有保暖作用的）空心墙，夹壁墙
  a wall consisting of two walls with a space between them, designed to prevent heat from escaping
  1. cavity wall insulation
     空心墙隔热

柯林斯词典

• N-COUNT (隔音或防寒的)空心墙，夹层墙
  Acavity wallis a wall that consists of two separate walls with a space between them. Cavity walls help to keep out noise and cold.
  1. ...cavity wall insulation.
     空心墙隔音材料

英英释义

noun

• a wall formed of two thicknesses of masonry with a space between them

双语例句

• Testing and Nonlinear Finite Element Analysis on Cavity Wall Structure
  空斗墙砌体结构检测与非线性有限元动力分析
• Conclusion Bonding resin could distinctly reduce microleakage and assure good adaptation between the cavity wall and amalgam.
  结论应用树脂粘结剂可增加充填体与洞壁密合度，明显减少银汞合金充填微渗漏。
• Influence of cavity wall elasticity on resonant frequency of small underwater cylindrical Helmholtz resonator
  腔壁弹性对水下小型圆柱形亥姆霍兹共振器共振频率的影响
• Research and finite element analysis on the steel frame structure with new infilling cavity wall
  新型砌体复合填充墙钢框架体系试验研究及有限元分析
• As a special masonry structure, cavity wall masonry is well accepted in rural areas of our country due to its low cost.
  空斗墙砌体作为一种特殊的砌体结构，由于其造价低廉，我国很多农村地区建房都采用这种结构。
• According to the wall testing process, we put finite element numerical simulation on the cavity wall which is set the ring beam but without structural concrete column, using discrete model to analysis the principal stress, cracks distribution and displacement of the wall.
  参照墙体试验过程，对设置圈梁但无混凝土构造柱的空斗墙体进行有限元数值模拟，采用分离式模型对墙体的主应力、裂缝分布与墙顶位移变化进行分析。
• One is that the same to that of the cavity wall. The other is that the pressure of equilibrium radiation field is only connected with the system equilibrium temperature.
  得到两个结沦：（1）平衡辐射场内部的压强与腔壁受的压强相同：（2）平衡辐射场的压强只与系统平衡时的温度有关，与其它性质无关。
• This numerical simulation on gas penetration, pressure field, displacement process of melt-gas boundary in different time, and skin melt forming on the cavity wall is developed for GAIM parts.
  该研究对气体的穿透过程、压力场分布、小同时刻熔体/气体边界的移动状态以及在模壁上形成表层聚合物熔体壁厚的过程进行了气体辅助注射成形充模流动的实例数值模拟研究。
• After entering the chamber, because of edge effects by the cavity wall, the flow rate of blank uneven, showing a distinct layered flow.
  在进入腔体以后，因边部受到腔体壁的影响，坯料的流动速率不均匀，可见明显的分层流动。
• The three main problems faced by water pump are leakage, vibration noise and corrosion of the impeller and water cavity wall.
  汽车水泵的三个主要故障是泄漏、振动噪声和叶轮或水腔内的腐蚀。